B & M Rifles and Cartridges - Company Message


500 MDM


The 500 MDM is currently the largest cartridge that can be put on a Winchester M70 without major modifications.   It is our biggest cartridge in true .500 caliber.    It is designed as a heavy hitter to duplicate and exceed the ballistics of the 500 Nitro express, it does this with ease.    Custom designed 550 gr bullets at 2250 fps.  With the designs of the new CEB and North Forks one would never need a heavier bullet than the 500 gr CEB #13 profile.     All this on a Winchester M70 with a 20 inch barrel and comes in a 8-8.5 lbs. 

These rifles do require a stock from Accurate Innovations that has the aluminum chassis built in to absorb recoil and to keep from cracking the stock.   Many of my rifles have Accurate Innovations stocks.    They are simply the finest stock that can be put on a big bore rifle.



We have many custom designed bullets available for the 500 MDM at reasonable prices.    For the largest of dangerous game we have proper solids that have been proven in the field along with expanding Non Conventional bullets.

The first outing for the 500 MDM was in Australia in 2009 for buffalo herd reduction and a couple of very fine trophy bulls.    Of 13 buffalo taken with the 500 MDM, 13 hit the ground where they stood.   I was using a 470 gr SSK/Lehigh Copper HP at 2425 fps backed with a 510 gr SSK/Lehigh Solid at a reduced velocity of 2200 fps.  Results were extraordinary, and final!







A Winchester M70 that was chambered from Winchester in 300 RUM is required for the 500 MDM.   Winchester did extensive modifications to this action to accommodate the RUM case.    Normally I have a few of these on hand for conversion if needed.



Andy and the very first




Early in 2014 my friend Andy started thinking about a "Dangerous Game Rifle".
After a bit of processing he contacted me about a 500 MDM.    Problem is, Andy was "Wrong Handed"...................   Meaning he needed a LEFT HAND 500 MDM, and there had never been such a thing.    Winchester never made a RUM based action in left hand.    

However, it just so happened that I had ordered two Montana Actions to experiment with, both long RUM based actions.    Montana is basically a Winchester  M70.    One of these just happened to be "Wrong Handed".............
I had ordered a left hand action for a PH in Zimbabwe, which later backed out on the build, lucky for Andy, as he decided to proceed.    Nearly before I could send the action to SSK for the 500 MDM build, Andy had also decided to complement his rifle selection with a new 416 B&M, which I try to keep a few left handed Winchester WSM actions when I can find them, and had one for Andy.

I had concerns about the build, as we had not worked with a Montana before, but since I specified RUM action, there was no reason it would not work as good as the Winchester, so off it went to SSK Industries.     Andy contacted Wes at Accurate Innovations and got two beautiful stocks in the works for his rifles.

500 MDM
500 MDM
Finally the day arrives that Andy's rifles are finished, and I have the 500 MDM in hand. 









500 MDM Top
500 MDM Top
416 B&M Bottom
At his request I had to put a big ugly EOTech red dot system on the rifle!   The stocks from Accurate Innovations were simply gorgeous, and to top it off with something so ugly was working on my nerves and OCD just a bit...........



Both rifles finished in black matte GunKote, both turned out very nice.    The new Left hand Montana fed, functioned and retained 100%, EXCEPT with the mighty #13 Solids, in which they bumped the bottom of the feed ramp and brought everything to a stop.    Andy's first hunt was coming up in a matter of a couple of weeks, a New Mexico bear.    He wanted to use the 500 MDM for this, so we used a 335 Raptor at 2800 fps.   With Talon Tips these bullets fed like butter in the Montana 500 MDM.    It was decided that Andy complete this hunting trip for bear, then send the rifle to SSK Industries and let them tune it for the #13 Solids, in which Andy would then use the rifle in Zimbabwe on his first elephant hunt.

Andy was very successful on his bear hunt, hitting the bear with the 335 tipped Raptor, the bear never took a step and hit the ground stone cold.  There was never a doubt, Andy spent nearly a week here with me working with his rifles.   He had not had much experience with big bores, but in no time at all he controlled the 500 MDM and handled it extremely well, making it look easy.   He also made a believer out of me with the EOTech, as Andy could stand at 25 yards and snap shots off very quickly knocking the center out of anything he shot at with it.    The rifle was working very well for him when he left me, and it worked perfect for him on this bear.

As soon as he returned the rifle was off to Brian at SSK Industries, I had already sent a bag full of dummy rounds loaded with the 500 gr #13 Solids.  Brian's mission was to get this rifle to feed and function 100% with these, as  in a couple of weeks Andy was off to Zimbabwe for elephant, and needed this rifle.
Brian had the rifle sorted out in a couple of days, on its way back to Andy, piece of cake............   SSK Industries does not suffer any issues when it comes to understanding how to make a DGR work, and in addition, they understand bullet performance, and why superior performance is required in the field.    SSK Industries, Brian Alberts, JD Jones, nor myself will settle for less than desirable performance whether in rifle, cartridge, or most important the bullet required for the mission at hand, and in this case the .500 caliber 500 gr #13 Solid.

Both 500 MDM and the #13 500 gr Solid had proven itself over and over again in the field, just as it did in all the prior test work done here.    I had taken elephant myself, Brent below had stopped a charging elephant with his at very close quarters (See Below), Stan had used his 500 MDM on multitudes of elephant, including the giant 90+ pounder you see below.    Penetration straight and extreme, along with hitting hard up front and doing a lot damage.    Well, once again the 500 MDM and the #13 500 Solid did its job, this time for our friend Andy, and did it with ease.   

Andy's first elephant was a brain shot putting the elephant straight down and found back in the spine.     The second elephant the bullet went through the left shoulder on a quartering shot and found on the opposite HIP........ That is a very long distance.   This elephant went 35 yards and was down for the count.

Andy also took a zebra with is 416 B&M, 60 yards it dropped immediately with the 225 Raptor at 2900+ fps, bullet passing through and through.
But that's another story for the 416 B&M Page.............

Andy my friend, I can no longer complain about that ugly EOTech on our rifle, you simply make it shoot too good for any further complaints.    Congratulations on your success, and we look very much forward to hearing of your upcoming adventures with your 500 MDM at your side.............................





Stan and his search for the


A couple of years ago Stan approached me about a 500 MDM I had on hand.   We came to terms on it and since that time Stan has used his 500 MDM extensively on his "Quest for the 100 Pounder".   For those not versed in elephant hunting, that means 100 pounds of ivory per side.   I don't know exactly how many elephants Stan has taken the last couple of years with his 500 MDM, but I believe it is on the other side of 25+.   This year, he came very close to getting his dream come true elephant.   This elephant went well into the 90 lb category.    


Soaking wet Stan might make 125 lbs.   With his 500 MDM to reduce recoil some, he uses the 500 gr #13 Solid from Cutting Edge Bullets at 2250 fps.   As you can see, he has put the rifle and this load to work for him to his advantage.

Congratulations Stan, and we look forward to following your continued Quest, and your many adventures with your 500 MDM.




500 MDM back in Australia

We recently returned from yet another hunting adventure with Paul Truccolo.  Earlier in the year Paul asked if I wanted to come down under and give him a hand with some of his herd reduction and management program for his buffalo, naturally I found it hard to resist.   

Back in 2009 I had taken the very first 500 MDM, a 21 inch hi polish blue with a new myrtle stock from Accurate Innovations.   You can see this rifle below and some of the work it did then.   I decided to modify the rifle since then, had the stock refinished and hand checkered, the barrel shortened to 19 inches, and the rifle Gunkoted matte black.  

This trip I was shooting a variety of Cutting Edge Bullets, from 335 gr all the way to 450s.    Lighter bullets, 335, 350, 365 were all running around 2700 fps, and did a great job.   Overall I took 21 buffalo and 3 pigs with the rifle, and at no time did it let me down in any way.   I did take a great bull using the 350 gr ESP Raptor at 2700 fps.   Shoulder shot, bull dropped at the shot.
On this Buffalo shoot I used mostly light for caliber bullets, this was test work, and we recommend strongly for buffalo you use the heavier CEB and North Fork bullets designed for buffalo, Cutting Edge, the 410 HP/450 Solid or 450 HP/500 Solid combinations, from North Fork the 450 CPS/FPS combinations.




2013 & Brent's 500 MDM....................

Since Brent took my favorite  500 MDM home in 2012 he has been putting it to work.  I know of two trips he took it to Africa with great success.   Below is a buffalo he took this year, Brent and his lovely wife...........


Below take a look at a piece of video from Brent, this was on his 2013 trip and a cow elephant charged them at very close range.   Brent did all the shooting with his 500 MDM and 500 gr #13 Solids, as you can see, the elephant was stopped in its tracks.   One of those bullets was found all the way from frontal head shot in the hip.  

Hitting the perfect brain shot is extremely challenging on elephant, even when standing still at close range, much less a sudden charge at extremely close range.
What you see here is what is termed a "Stopping Rifle".   Even missing the brain entirely on this charge, the heavy caliber bullet of the 500 MDM was able to stop this charge in its tracks, and keep this elephant down for the duration.   After the first shot, the elephant was put down and was not able to recover, even though Brent missed the brain.   The rifle/cartridge did its job, and very likely saved the lives of both Brent and his PH, and videographer.   


You need Flash Player in order to view this.
Brent 500MDM
Elephant hunt Africa, Brent with custom rifle, the 500 MDM by B&M Rifles and Cartridges

New Nose Profile From North Fork Technologies


North Fork has now officially changed, and improved the nose profile of their entire solid FPS bullet line.   It is close, but not exact to the BBW#13 Nose Profile, which has proven excellent in terminal stability, and depth of penetration.   We have tested these, and they are indeed an improvement.





























Two New Bullets from Cutting Edge


Two new .500 caliber bullets from Cutting Edge are the 300 gr BBW#13 HP W25 and the 335 BBW#13 HP W24.   These are designed with a short nose profile, driving bands moved forward, so they can be seated deep, and used in the magazines of the B&Ms with W Talon Tips installed.

































April 2012

Just returned from South Africa in which we took a new Winchester M70 500 MDM with a  19 inch barrel to try out on a few species of plains game, wildebeast, eland, and oryx.     One of the objectives for the trip was to test the new 350 gr ESP Raptor from Cutting Edge Bullets.    It was a tremendous success, rifle, cartridge, and of course the bullet. 

Winchester M70 500 MDM
Winchester M70 500 MDM
19 inch Barrel















































This bullet at 2750 fps from the 500 MDM was devastating to say the 
least.   Massive destruction of tissue was observed, complete penetration in all cases, and impacts were quite impressive.

The Winchester M70 500 MDM 19 inch gun found a new home, in off all places, Winchester VA!  How about that?   A new friend of ours from Accurate Reloading, Brent Ebeling, came down for a visit wanting to shoot, handle and talk about 500 MDM as his next Dangerous Game Rifle.   We did that one Friday all day long.   Shot a few rounds to say the least, and Brent really liked my 19 inch 500 MDM, the only one of it's kind.   I like it too you know, or I would not have it!   I gave in, and Brent took it home, and is enjoying his new DGR very much.   I look forward to reporting back to you about Brent's adventures with it.






Horneber Brass Update----1/2013

This past month, January 2013, I have been working with both 450 BBW#13 Solid, 500 BBW#13 Solid, and 450 North Fork CPS all with RL 15, and the Horneber brass.   I have been able to get anything from 2200 fps to 2300 fps depending on the bullet, and no problems or issues with the Horneber 500 MDM brass.    Using 102.5 gr of RL 15 and 450 #13 Solid and 450 North Fork CPS is giving 2250 fps in the Horneber brass, no problems at all.  I even did temperature tests, let the ammo get to  110 degrees, and still no signs of pressure.   While we still cannot get to the full potential of the 500 MDM with the Horneber brass, we would be able to use it with RL 15 and 2200-2250 fps, which is more than enough to accomplish any mission at hand.  

December 2011

I report both good and bad, whatever the case may be when it comes to all the rifles and cartridges.    

First our Premium Horneber 500 MDM brass is not so good.   It's very soft, and is not able to withstand any sort of pressure at all without getting sticky in the chamber.    The very best solution I have for this brass is very light duty work.   This brass is only able to run the 500 BBW#13 Solid at 2000 fps without issues, and of course in RUM brass it will run from 2500 + without running into any problems!   We can also get the 450 North Forks, both FPS and CPS up to 2175 fps without running into problems, and in RUM brass we can run them into 2700 fps at low pressure!   So this is not good.    Currently I have NO GOOD SOLUTION for proper Head Stamped 500 MDM brass.    If you think you HAVE TO HAVE proper Head Stamped brass for your rifle, then the 500 MDM currently is not for you!  


I am having stamped on the barrels of the 500 MDM this;

500MDM/375RUM

This should cover one if any customs in the world decides to inspect head stamped ammo with the markings on the barrel.    



October 2011

I recently received some new stocks from Accurate Innovations for the 500 MDM rifles.   

This first one is Bastogne, and is the stock that is home to this stainless rifle.


Winchester M70 500 MDM
Winchester M70 500 MDM



































This is a Myrtle Stock by Accurate Innovations that they just happened to have in stock on hand.   It fit the 500 MDM rifles, I could not turn it down!


Winchester M70 500 MDM
Winchester M70 500 MDM
Myrtle Stock by Accurate Innovations

































July 2011

The 500 MDM was a grand success in Zimbabwe and South Africa in June.  It proved to be a serious hammer for large dangerous game, along with the BBW#13 Solids, NonCons, and the North Fork bullets.   See photos below.    

The 500 MDM performed so well and was so impressive that Andrew Schoeman, long time PH and friend, decided he really wanted a Winchester M70 500 MDM for his personal backup rifle.   Quite a compliment to the 500 MDM I would say.   Andrew will also be getting a new 9.3 B&M as his plains game rifle and loan out rifle for clients hunting plains game.   An excellent choice I think.  

In addition I had Cutting Edge Bullets make a run of 550 gr BBW#13 Solids for the 500 MDM.  I will be working up load data and terminal reports on that soon as well.













 

 February 2011

Have a look at Paul Truccolo's new Winchester M70 500 MDM.    20 Inch barrel, XX Turkish stock from Accurate Innovations, gunkote matte finish.


































Cutting Edge Bullets
500 BBW#13 Solid
450 BBW#13 NonCon HP

#13 Solids and NonCons
#13 Solids and NonCons
460 NonCon 500 #13 Solid
460 NonCon 500 #13 Solid
460 CEB BBW NonCon HP
460 CEB BBW NonCon HP












































North Fork 450 FPS and CPS

450 North Fork CPS-500 MDM
450 North Fork CPS-500 MDM
Trauma Inflicted on Witness Card
Trauma Inflicted on Witness Card
450 North Fork FPS-500 MDM
450 North Fork FPS-500 MDM


























Basic Load Data 500 MDM







More about NonCons---Non-Conventional Bullets.    Add "Conventional" to the Endangered Species List!






Zimbabwe 2011 With the 500 MDM using Cutting Edge Bullets and North Fork Bullets









Australia 2009 with the 500 MDM



























































500 MDM Rifles and More


















































Website Builder provided by  Vistaprint